You usually come across the names of HVAC contractors when you search for residential ac repair near me. You rely on them for heating and cooling services in Cypress, but do you know that they do so much more than just repairing the air and heating systems. And here are the few services that we offer at Texas Star Heating & Cooling:

Have you lately started noticing water leaking out of your A/C and been wondering what could be causing it? Well, whatever the reason, you certainly need to connect with a professional heating & cooling company to fix the problem for you.

Meanwhile, lets discuss three major reasons that cause leakage in an air conditioner:

With heating and cooling system becoming the integral part of every residential as well as a commercial building, it is understandable if you go for a toss as an owner when your HVAC system faces a breakdown.

The first question that comes to the mind is how much would a new furnace cost. Well, though it is difficult to determine the exact cost of the furnace replacement that your system requires, there are certain factors that can determine how much the HVAC services provider will charge you.

Indoor air quality is one of the most important yet neglected things in our routine life. As long as our HVAC system is keeping our home warm in winters and providing cooling in summers, it's all good. But what happens when it breaks down or something disrupts the regular functioning of the system? Our lives come to a halt and it becomes difficult to live comfortably in our own homes.

You may think of replacing your air conditioning unit yourself, but doing so will cause you more harm than good. You may want to do it in order to save money, but improper installation may cost you a lot of money in the long run. If you want to get Ac Installation Services in TX, think about hiring the services of experienced professionals rather than doing it yourself. Why professionals? What are the benefits of professional Ac installation? Well, read below to know the benefits of professional Ac installation:

Whenever you get an AC installed, its important that you get the right installation techniques. Monitoring the HVAC installation techniques might not seem interesting to you, but improper equipment installation can cost you a lot by decreasing the heating and cooling efficiency by up to 30%. Not just this, but there are several other reasons as to why you should pay attention towards proper AC installation techniques and get the Best AC Installation in Cypress.

An HVAC system is well known to offer comfort, luxury and style to your home. It is difficult to understand this complex unit, only professionals know how to expertly install, repair or replace the heating and cooling system. Hiring the right HVAC Company is crucial for so many reasons; this blog post will help you decide which company is best for you?

The foremost important thing is to check for their experience, credentials and customer reviews & feedback. Here you will find a list of questions to ask before you hire an expert HVAC Company Cypress TX or we can call it a complete checklist that you must consider for choosing the best HVAC technician.

Furnaces have reformed more than you think; it was all different some years ago. Here you will read how they have changed, why and when do you need to replace an out-of-date and inefficient furnace? You may not have realized but the furnace you are using could be inefficient or outdated. Today's high-efficiency, a natural gas-powered furnace is much more advanced and comes with a lot of features. They take up less space, uses less home Furnace Heating Energy, are extremely safe, and provide better control over the temperature. There are many reasons why you should think of buying a new HVAC system over an older furnace unit, here are some:

This year 2017 in Cypress, TX. we are finding an alarming number of Evaporator coil Refrigerant leaks. It is a must that these replacement coils get installed correctly. A lot of the manufactures have gone from copper to aluminum and not supplying the metering device. Also, 410A

Whether you are installing Mitsubishi, Fujitsu or Daikin, the most important thing with the ductless mini split air conditioners

During our service calls in Cypress Texas we have been finding an amazing amount of gas leaks in new homes and existing furnace change outs. We would recommend from time to time to go into your attic and check for gas leaks, which smells like rotten eggs. Have your furnace serviced at

Superheat is the difference between the actual temperature of the refrigerant gas as it leaves the evaporator and the boiling point temperature of the refrigerant in the evaporator coil. After boiling, the refrigerant continues to warm up. The number of degrees it “warmed up” after boiling is called the superheat. Under worse case conditions (low load or ** orifice systems), the refrigerant in the evaporator boils off near the end of the evaporator coil. To make sure the liquid does not enter the compressor under the worse case condition (low load), the refrigerant manufactures of air conditioning equipment, publish charts indicating what superheat should be, at a given indoor wet bulb measurement and an outdoor air temperature. Superheat is your best indication on a fixed orifice system of the proper refrigerant charge. If everything else is working properly and the actual superheat is too high, add refrigerant. If it is too low, remove refrigerant. ** Orifice is a refrigerant metering device. Sometimes called a piston.**

You don't have to call in an air conditioning technician in Houston, Texas immediately for what could just be a minor problem. You should check the air filter first if it is dirty.  If the thermostat is set to cool and the temperature in the room isn't dropping, there could be ice build-up on the Evaporator Coil due to low airflow from the dirty air filter. It will defrost the evaporator coil faster if you turn the thermostat fan switch from auto to on. Check to make sure you have some airflow, then in one-hour re-check it, you should have more airflow, if you do, let it run on the fan for two more hours, then turn the thermostat back to auto and go back to cooling. However, you should still have it serviced.

A national account provider called us to look at a problem at an auto parts store in Richmond Texas, which was having a problem with their hvac systems. The company that installed the Gridpoint HVAC Energy Management System used thermostat wire instead of twisted shielded cable causing interference with the sensors. We came in and removed 800 feet of thermostat wire and installed the shielded cable as per the specifications on the blueprint. This resolved the problem the auto parts store was having.

These products are used in systems that are leaking refrigerant. The manufactures of these products say they do no harm to the system, but air conditioning systems consist of metering devices that may be fixed piston type or expansion valve type. Pistons have metering bore holes. And they have screens in the fitting that catches debris that may have been missed by the filter dryer.

We serviced two gas furnaces in the attic in Cypress, Texas, before the heating season started. We found the gas vent exhaust pipe disconnected in the attic, without this furnace inspection it would have been venting carbon monoxide into the customer’s attic. Please have your gas furnace checked out before you use it. Hope this helps.

We were called out to a house in Katy Texas, because a gas furnace was not operating right. We check out the furnace and it was kicking out on the high limit safety. We quickly diagnosed it as an air flow issue. We checked the air filters to make sure they were clean. Then we checked the static pressure and it was (1.10). The flex duct came from the return into the back end of the furnace. We recommended to the customer to add a plenum on the back end of the furnace giving us the space we needed to add a new return and tie in the existing return. We messured the static pressure and it was (.10). We checked the operation of the gas furnace and now it was not kicking out on high limit safety. More information on air flow can be found on my Air Flow Blog article.

Here is why: Most home inspection services only look at the HVAC system. They will write down the model numbers and serial numbers and run the system. They will check the return temperature while it's running and the supply air temperature and tell you what the difference is in the temperature. They will only notice obvious signs. An a/c contractor should take a static pressure reading, this will tell them about the duct work ie: too small of a return air and supply air duct issues.

In the Katy, Cinco Ranch, and Cypress areas of Texas we are finding gas furnaces installed vertically in attics. This type of installation should be avoided and here is why: Gas furnaces nowadays are more compact than ever. The airflow goes in the furnace through the side when installed vertically and in the bottom when installed horizontally. This is the best way to install it, and here is why: When you install a furnace vertically because of its size you are limited to the opening. The manufacturer's installation instrutions show that they want you to use a square opening not less than the recommended size. If you use sheet metal duct work with a liner you will loose a total of three inches on the four sides of the inside of the duct. Sheet metal wrapped with insulation on the outside does not reduce the inside dimensions.